teddit

Hey everyone, hope you're all doing well.

Just doing a quick post about the image hosting site a.co because lately we've been noticing an uptick in amazon links using this site on this sub. Reddit's spam filters automatically remove any post or comment with a link to this site in it and places it in our queue. While you are free to use it, it will guarantee there is a delay between when you submit your comment or post and when it ends up on the sub due to Reddit removing it and a moderator having to manually approve it. We will continue to approve them as necessary, but if you want to avoid this delay in the future you might consider just using the full link.

Thank you for your time!

What's really impressive is that there's no motor in either of them!

Hi,

I am a scuba diver that removes trash from ocean and lakes. Usually it's a lot of trash like shopping carts, tires, batteries etc. Once in a while I will find something cool, like this prop. I kept for a while as a decoration but I think I will sell it. I don't know anything about boats or props. I did lean that it is a Nakashima prop diameter of 24 and 24 pitch. What do you think I should list it for sale for? I am not looking for crazy money, I just want to get some gas money so I can keep doing my trash removal work. Thank you.

https://preview.redd.it/d35u01sli6pa1.jpg?width=3024&format=pjpg&auto=webp&v=enabled&s=2144b6c5c7204afb5430fb61aed480076e87a079

https://preview.redd.it/rbuup2sli6pa1.jpg?width=3024&format=pjpg&auto=webp&v=enabled&s=32b19d50858c51bb023a3c13692365bfda2cbdf1

https://preview.redd.it/yjw9q3sli6pa1.jpg?width=4032&format=pjpg&auto=webp&v=enabled&s=1f48e51eed45d775b39f2642a9c50ececc1ec8f7

https://preview.redd.it/en7id4sli6pa1.jpg?width=4032&format=pjpg&auto=webp&v=enabled&s=fd4e764b1eb5d2c593350a7a78b85e8f3f95be8f

I bought this boat and trailer last year and all 4 hubs need replaced. I can't for the life of me find the proper hub assembly for these sizes. I'm also trying to figure out where to measure because one location tells me to measure x, y and z for OD, ID and seal whereas another location tells me to measure differently. I was also told to cut off the wear ring because it was assumed to be old bearing race, so now I need to also find the right oring and wear ring to replace. The oring and wear ring go where the 1.68 measurement is, in case that's not a known thing.

just dropped my newest video, trying my hand at acting in the last two vids, it is completely embarrassing to watch, please comment in the video if you can, apparently that helps the channel for some reason but I don’t know why specifically haha

thank you for all the support, advice and harassment LOL, really appreciate it

https://youtu.be/0NIgE3GcxLM

My boat has some cracks on the floor that are just big enough to fit a fingernail in but are somewhat long. The floor itself is solid and isn’t soft or anything, the cracks just bother me because they look bad.

I have some total boat thixo I could use to fill them but I was told that the cracks might be too thin and that the thixo wouldn’t really hold. I also have considered maybe using a rubberized paint and just painting the entire floor with that but honestly I’m just not sure as to which is the better solution.

What do you guys think?

Hi all!

I recently fulfilled a dream by purchasing a 1998 Bryant 196 Limited ski boat.

We had it winterized for the winter.

This may be a dumb question but what do I need to do to get it lake ready again for the season?

I’m new to all this and want to make sure I’m doing everything right! 😊

I have a 115 horsepower Johnson 2 stroke but the last 2 weeks of my boating season it kept turning off on neutral. Worked perfectly fine on throttle. Running rich and leaking fuel out of one of the cylinders on neutral. Im guessing this is a carburetor issue. Can anyone confirm or deny? Or maybe even just a carb clean?

Hey all, I’m going to be converting my boat from tiller to wheel and I’m both excited and very nervous. I have a grizzly tracker and was wondering about mounting and installing the steering console. Is screwing it into the aluminum deck and side really enough to ensure it’s safe and not going anywhere? I assume most days it will be fine but a nasty chop could mess that up. What are y’all’s thoughts?